Bose POWERSHARE PS602 230V EU

Description

Key Features

• PowerShare Technology – Patented PowerShare technology allows the total 600
watts of power to be shared asymmetrically across all outputs, as each output
is capable of delivering full power. Instead of selecting amplifier power based
on the needs of the largest zone, installers now have the freedom to use total
amplifier power in the application. This enables more flexibility during the initial
design, or later on-site when making unplanned changes that take advantage of
surplus power.
• Load-Independent Outputs – Each channel can be configured for low-impedance
(4-8 Ω) or high-impedance (70/100V) applications without bridging, use of
jumpers, or software settings.
• DFL™ System – The Dual Feedback Loop system, inherited from the field-proven
Bose PowerMatch® amplifier line, improves performance and reliability through
continuous monitoring and control of both the current and voltage delivered
to each output load. This combination provides improved linearity and lower
distortion, while protecting loudspeakers.
• Integrated Loudspeaker Processing with Optional PowerShare Editor
Configuration – For applications requiring additional signal processing the
PowerShare Editor Software offers real-time selection and control of Bose
loudspeaker EQs, 9-band PEQs, matrix mixing, crossover, delay, and mute/output
polarity through a USB connection. For basic setups without a PC, rear-panel
settings allow installers to recall Bose loudspeaker equalization and protection
per output channel. These features eliminate the need for an external signal
processor in many applications.
• ControlCenter Zone Controller Accessories – Bose ControlCenter CC-1 zone
controllers can be directly attached for remote adjustment of amplifier outputs,
further extending stand-alone amplifier applications.
• Auto-Standby – Designed to save power consumption when not in use.
PowerShare amplifiers can be configured to automatically enter standby mode
when the audio signal falls below a set threshold, then wake when audio returns.

Applications

Designed for a wide range of applications,
including:
• Performing arts venues
• Houses of worship
• Conference centers
• Retail stores
• Restaurants and bars
• Hospitality venues

Technical Specifications

POWER RATING
Amplifier Power 2 x 300 W (THD+N < 0.04%, 1 kHz, 4-8 Ω, 70/100V)
Maximum Power per Channel 600 W @ 4-8 Ω, 70/100V
Gain (Low-Z mode) 44 dB, RCA (unbalanced) inputs; 32 dB, Euroblock (balanced) inputs
Gain (70V mode) 47 dB, RCA (unbalanced) inputs; 35 dB, Euroblock (balanced) inputs
Gain (100V mode) 50 dB, RCA (unbalanced) inputs; 38 dB, Euroblock (balanced) inputs
AUDIO PERFORMANCE
Frequency Response 4-8 Ω: 20 Hz – 20 kHz (+/- 0.5 dB @ 1 W); 70/100V: Same as 4-8 Ω with 50 Hz high-pass filter
Channel Separation (Crosstalk) > 85 dB @ 1 kHz, > 65 dB @ 20 kHz
Signal to Noise Ratio 100 dB (at rated power, A-weighted)
AUDIO INPUTS
Input Channels 2 unbalanced, 2 balanced
Connectors Stereo RCA, 3-pin Euroblock
Input Impedance 10 kΩ (RCA), 20 kΩ (Euroblock)
Maximum Input Level 20 dBu (at 12 dBu sensitivity setting)
Sensitivity-10 / -2 dBV, RCA inputs; 4 / 12 dBu, Euroblock inputs (low / high sensitivity)
AUDIO OUTPUTS
Outputs 2
Connectors 2-pin inverted Euroblock
INTEGRATED DSP
A/D and D/A Converters 24-bit / 48 kHz
Processing Functions Matrix mixer, loudspeaker EQ, real-time 9-band PEQ, Vpeak/Vrms limiters, delay, band pass, mute/output polarity
inversion
Loudspeaker Presets Flat, DS16, DS40, DS100, FS3B, 402, 802, MA12EX, RMU105 and RMU108
Audio Latency < 1 ms (any input to speaker output)
INDICATORS AND CONTROLS
Power LED Solid green: Power is on. Blinking green: Unit is in standby mode. Solid amber: Thermal fault. Solid red: Supply fault.
Input Signal LED Green: Signal present. Amber: Input is near clipping. Red: Input is clipping. Solid red: Indicates a fault.
Output Limit LED Amber: Amplifier limiting an output. Blinking red: Amplifier muted. Solid red: Indicates a fault.
Controls, Front Panel Power On/Off
Controls, Rear Panel Amplifier mode DIP switches, loudspeaker EQ dials, output attenuators
ELECTRICAL
Mains Voltage 100 VAC – 240 VAC (±10%, 50/60 Hz)
AC Power Consumption 120 VAC: 14 W (Standby), 700 W (Max) 230 VAC: 14 W (Standby), 700 W (Max)
Mains Connector Standard IEC (C14)
Maximum Inrush Current 14.14 A (230 VAC / 50 Hz), 8.04 A (120 VAC / 60 Hz)
Protections High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage
PHYSICAL
Dimensions (H x W x D) 44 mm x 483 mm x 414 mm (1.7” x 19.0” x 16.3”)
Shipping Weight 6.9 kg (15.3 lb)
Net Weight 5.5 kg (12.2 lb)
Cooling System Microprocessor controlled, variable speed fans, left to right air flow
GENERAL
Inputs (Control) RJ-45 remote input for volume control using the CC-1 ControlCenter zone controllers, or for connection to the CV41.
USB input for configuring the amplifier with PowerShare Editor software. Mute input control.